Standard Svensk standard · SS-EN ISO 10846-2:2008

Akustik och vibration - Laboratoriemätmetod för vibroakustiska överföringsegenskaper hos elastiska element - Del 2: Dynamisk styvhet vid rätlinjig rörelse hos vibrationsisolatorer - Direktmetod (ISO 10846-2:2008)

Status: Gällande

Köp denna standard

Standard Svensk standard · SS-EN ISO 10846-2:2008

Akustik och vibration - Laboratoriemätmetod för vibroakustiska överföringsegenskaper hos elastiska element - Del 2: Dynamisk styvhet vid rätlinjig rörelse hos vibrationsisolatorer - Direktmetod (ISO 10846-2:2008)
Prenumerera på standarden - Läs mer Dölj
Pris: 1 320 SEK
standard ikon pdf

PDF

Pris: 1 320 SEK
standard ikon

Papper

Pris: 2 112 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ
Provläs denna standard
Omfattning
This part of ISO 10846 specifies a method for determining the dynamic transfer stiffness for translations of resilient supports, under specified preload. The method concerns the laboratory measurement of vibrations on the input side and blocking output forces and is called “the direct method”. The method is applicable to test elements with parallel flanges (see Figure 1). Resilient elements, which are the subject of this part of ISO 10846, are those which are used to reduce the transmission of vibration in the lower part of the audible frequency range (typically 20 Hz to 500 Hz) to a structure which may, for example, radiate unwanted fluid-borne sound (airborne, waterborne or others), and the transmission of low-frequency vibrations (typically 1 Hz to 80 Hz), which may, for example, act upon human subjects or cause damage to structures of any size when vibration is too severe. NOTE 1 In practice, the size of the available test rig(s) can restrict the use of very small or very large resilient supports. NOTE 2 Samples of continuous supports of strips and mats are included in this method. Whether or not the sample describes the behaviour of the complex system sufficiently is the responsibility of the user of this part of ISO 10846. Measurements for translations normal and transverse to the flanges are covered in this part of ISO 10846. The direct method covers the frequency range from 1 Hz up to a frequency fUL, which is usually determined by the test rig. NOTE 3 Because of the large variety of test rigs and test elements, fUL is variable. In this part of ISO 10846, the adequacy of the test rig is not defined for a fixed frequency range, but on the basis of measured data, as described in 6.1 to 6.4.

Ämnesområden

Allmänt Bullermätning (17.140.01)


Köp denna standard

Standard Svensk standard · SS-EN ISO 10846-2:2008

Akustik och vibration - Laboratoriemätmetod för vibroakustiska överföringsegenskaper hos elastiska element - Del 2: Dynamisk styvhet vid rätlinjig rörelse hos vibrationsisolatorer - Direktmetod (ISO 10846-2:2008)
Prenumerera på standarden - Läs mer Dölj
Pris: 1 320 SEK
standard ikon pdf

PDF

Pris: 1 320 SEK
standard ikon

Papper

Pris: 2 112 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ

Produktinformation

Språk: Engelska

Framtagen av: Akustik och buller, SIS/TK 110

Internationell titel: Acoustics and vibration - Laboratory measurement of vibroacoustic transfer properties of resilient elements - Part 2: Direct method for determination of the dynamic stiffness of resilient supports for translatory motion (ISO 10846-2:2008)

Artikelnummer: STD-67053

Utgåva: 2

Fastställd: 2008-08-25

Antal sidor: 44

Ersätter: SS-EN ISO 10846-2